2014 Dodge Charger

Ideas and discussion of what to do with the CAN Bus ( i.e. XMDirect, iPod, Carputer, etc... )
nemiro
What's hacking?
Posts: 26
Joined: 2015 Feb 07 20:06

Re: 2014 Dodge Charger

Post by nemiro » 2017 Oct 15 01:14

Well, for whatever reason, the RHR decided to behave, now. So, disregard my last request. Now if I could just figure out a 'Clock Fix' for the RHR, like there is for the RER/REN, then I would be styling :)

poop713
CAN? Tin or aluminum?
Posts: 56
Joined: 2017 Feb 09 23:31

Re: 2014 Dodge Charger

Post by poop713 » 2017 Oct 24 23:45


poop713
CAN? Tin or aluminum?
Posts: 56
Joined: 2017 Feb 09 23:31

Re: 2014 Dodge Charger

Post by poop713 » 2017 Nov 07 21:08

I have some stuff from a 2015 Chrysler 200

2015 chrysler 200 CANbus ID’s
CAN-IHS

Steering wheel buttons
4a3#

Left button
4A3#07F8008000040000

Right button
4A3#07F8080000040000

Down button
4A3#07F8020000040000

Up button
4A3#07F8200000040000

Ok button
4A3#07F8800000040000

Behind steering wheel up left side
4A3#07F8000002040000

Behind steering wheel down left side
4A3#07F8000008040000

Behind steering wheel center button left side
4A3#07F8000800040000

Behind steering wheel up right side && volume up
4A3#07F80000000C0000

Behind steering wheel down right side && volume down
4A3#07F8000000240000

Behind steering wheel center button right side
4A3#07F8000000840000

Rpm’s
09A

Speed
098

Vin number
3d3#

Shifter
190# [5]

Park
190#0422000000

Reverse
190#0442000000

Neutral
190#0462000000

Drive
190#0482000000

L
190#04A2000000

2014ChargerAWD
How the heck did I end up here?
Posts: 1
Joined: 2017 Nov 15 23:33

Re: 2014 Dodge Charger

Post by 2014ChargerAWD » 2017 Nov 15 23:44

Good day,

New to the forum and not at all a programmer or hacker (as of yet). I have a malfunctioning #carconnect and a perfectly good awesome Tazer. I have a 2014 Dodge Charger AWD.

What I am most interested in is the ability to dim the interior dash/Uconnect lighting to zero when turning off the exterior lights. As the car is now, factory, it goes to parade mode, full 100% bright when the lights are turned off. #carconnect was able to program the car to go to stealth mode when you roll the dimmer to off. It would turn off exterior lights (it would turn them off sequentially oddly, from left to right on the exterior from the drivers perspective) and the interior. If you rolled the switch back up, the would come back on. The side effects were that that the door locks did not work in stealth mode, nor would the fob (except remote start and trunk open).

ZAuto had a 'Full Dim" option that worked similarly, but it was menu item in zauto menu only accessible from RUN, not running. Whereas #carcoonect was dynamic.

My question on this thread: Has anyone been able to make their car have a safe way to go into 'stealth mode' and come out of it while keeping door locks working? ZAuto says it's not safe the way avidcode was doing it. Dynamically.

Thanks for any reply. My #carconnect board seems to have a loose connection. It only works if I twist the case... and then it shows the menu. It's dodgy. Wish I knew what to fix on it. The hardware guy tried to resolder the board, but it didn't work. Is there a way to get the code off and transfer to a new unit?

Thank you.

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests